304 is a variation of the basic 18-8 grade, Type 302, with a higher chromium and lower carbon content. Lower carbon minimizes chromium carbide precipitation due to welding and its susceptibility to intergranular corrosion. In many instances, it can be used in the ”as-welded“ condition, while Type 302 must be annealed in order to retain adequate corrosion resistance. Type 304L is an extra low-carbon variation of Type 304 with a 0.03% maximum carbon content that eliminates carbide precipitation due to welding. As a result, this alloy can be used in the ”as-welded“ condition, even in severe corrosive conditions. It often eliminates the necessity of annealing weldments except for applications specifying stress relief. It has slightly lower mechanical properties than Type 304. Typical uses include architectural moldings and trim, kitchen equipment, welded components of chemical, textile, paper, pharmaceutical and chemical industry processing equipment.
Standard Specification
| Thickness | 4mm-100mm | ||||||
| Width | 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc | ||||||
| Length | 2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc | ||||||
| Surface | 2B, 2D, BA, NO.4, NO.8, 8K, mirror, checkered, embossed, hair line, sand blast, Brush, etching, etc | ||||||
| Finish | Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) | ||||||
| Form | Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange) etc. |
||||||
|
Surface finish |
Thickness |
Size |
Characteristics |
Application |
|
NO. 1 |
3-100mm |
Width: 1500/1800/2000mm; |
Finished by hot-rolling, annealing and pickling, characterized by white pickled surface |
Chemical industry equipment, Industrial tanks |
|
2B |
0.2-6.0mm |
Width: 1000/1219/1500/1800/2000mm; |
Finished by heat treatment, pickling after cold rolling, followed by skin pass line to be more brighter and smooth surface |
General Application Medical Instruments,Tableware |
|
No. BA |
0.2-3.0mm |
Width: 1000mm,1219mm; |
Bright heat treatment after cold rolling |
Kitchen utensil, kitchen ware,architectural purpose |
|
NO.4 Satin |
0.3-8.0mm |
Width: 1000/1219/1500mm; |
Polishing with No. 150 to No.320 mesh abrasivesThe most popular finishes |
Milk & Food processing acilities, Hospital Equipment, Bath-tub |
|
8K Mirror |
0.3-10mm |
Width: 1000/1219/1500mm; |
A mirror-like reflective surface by polishing with finer abrasives over 800 mesh |
Reflector, Mirror, Interior-Exterior decoration forbuilding |
|
HL(Hairline) |
0.3-8mm |
Width: 1000/1219/1500mm; |
Finished by continuous linear polishing |
Architectural purposes, escalators, kitchen ware vehicles |
Steel is an alloy of iron and carbon. Stainless steels are steels containing at least 10.5% chromium, less than 1.2% carbon and other alloying elements. Stainless steel’s corrosion resistance and
mechanical properties can be further enhanced by adding other elements, such as nickel, molybdenum, titanium, niobium, manganese, etc.
|
Grade |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
N |
Cu |
|
201 |
≤0.15 |
≤0.75 |
5.5~7.5 |
≤0.060 |
≤0.03 |
16.00~18.00 |
3.5~5.5 |
- |
- |
0.08 |
|
202 |
≤0.15 |
≤1.00 |
7.5~10.00 |
≤0.060 |
≤0.03 |
17.00~19.00 |
4.0~6.0 |
- |
≤0.25 |
|
|
301 |
≤0.15 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
6.00~8.00 |
- |
||
|
302 |
≤0.15 |
≤1.00 |
≤2.00 |
≤0.035 |
≤0.03 |
17.00~19.00 |
8.00~10.00 |
- |
||
|
304 |
≤0.07 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
18.00~20.00 |
8.00~10.50 |
- |
||
|
304L |
≤0.030 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
18.00~20.00 |
9.00~13.00 |
- |
||
|
310S |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
24.00~26.00 |
19.00~22.00 |
- |
||
|
316 |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
10.00~14.00 |
2.00~3.00 |
||
|
316L |
≤0.03 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
12.00~15.00 |
2.00~3.00 |
||
|
321 |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
17.00~19.00 |
9.00~13.00 |
- |
||
|
430 |
≤0.12 |
≤0.75 |
≤1.00 |
≤0.040 |
≤0.03 |
16.00~18.00 |
- |
|||
|
2205 |
≤0.03 |
≤1.00 |
≤2.00 |
≤0.030 |
≤0.015 |
22.00~23.00 |
4.5~6.5 |
2.5~3.5 |
||
|
2507 |
≤0.03 |
≤0.08 |
≤1.20 |
≤0.035 |
≤0.015 |
24.00~26.00 |
6.00~8.00 |
3.0~5.0 |
||
|
904L |
≤0.02 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.035 |
19.00~23.00 |
23.00~28.00 |
4.0~5.0 |
1.0~2.0 |
|
|
INCONEL 028 |
≤0.03 |
≤1.00 |
≤2.50 |
≤0.030 |
≤0.030 |
≤28.0 |
≤34.0 |
≤4.0 |
≤1.4 |
|
|
MONEL 400 |
≤0.30 |
≤0.5 |
≤2.00 |
- |
≤0.024 |
- |
≥63.0 |
- |
≤34.0 |
|
|
INCONEL 800 |
≤0.10 |
≤1.00 |
≤1.50 |
- |
≤0.015 |
≤23.0 |
≤35 |
4.0~5.0 |
- |
≤0.75 |
FAQ：
Q: What kind of work does your company do?
A: We are a business steel industry and trade. We mainly produces stainless steel plate/pipe/coil/round bars etc.
Q: What are the advantages of your company?
A: (1): Prime quality and Competitive price.
(2): Excellent experiences with after-sale service.
(3): Every process will be checked by responsible QC which insures every product's quality.
(4): Professional packing teams which keep every packing safely.
(5): Samples can be provided as your requirements.
Q: What is your terms of payment ?
A: Can be negotiated by both parties. If you have another question, pls feel free to contact us as below
Q: What about your price?
A: Our price is very competitive.
Pls feel free to contact us if you are interested in our products.
Q: How long is your delivery time?
A: Stock steel/Steel for simple cutting/Small amount of general standard steel: about 5-20 days for delivery; Custom steel/bulk steel: about 15-30 days for delivery. Contact us for specific delivery
times.
