According to the definition in GB/T20878-2007, stainless steel is mainly characterized by stainless steel and corrosion resistance, and the chromium content is at least 10.5%, and the carbon
content is not more than 1.2%.
Stainless steel is the abbreviation of stainless and acid-resistant steel. The steel that is resistant to weak corrosive media such as air, steam, and water or has stainless steel is called stainless
steel. The steel grade is called acid-resistant steel.
Due to the difference in chemical composition of the two, their corrosion resistance is different. Ordinary stainless steel is generally not resistant to chemical medium corrosion, while
acid-resistant steel is generally stainless. The term "stainless steel" does not simply refer to one type of stainless steel, but to more than one hundred industrial stainless steels, each developed
to perform well in its specific field of application. The key to success is to first understand the application and then determine the correct steel grade. There are usually only six steel grades
associated with building construction applications. They all contain 17-22% chromium, and the better grades also contain nickel. The addition of molybdenum can further improve
atmospheric corrosion, especially corrosion resistance to chloride-containing atmospheres.
Generally speaking, the hardness of stainless steel is higher than that of aluminum alloy, and the cost of stainless steel is higher than that of aluminum alloy.
Standard Specification
Thickness | 0.01mm-100mm | ||||||
Width | 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc | ||||||
Length | 2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc | ||||||
Surface | 2B, 2D, BA, NO.4, NO.8, 8K, mirror, checkered, embossed, hair line, sand blast, Brush, etching, etc | ||||||
Finish | Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) | ||||||
Form | Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange) etc. |
Surface finish |
Thickness |
Size |
Characteristics |
Application |
NO. 1 |
3-100mm |
Width: 1500/1800/2000mm; |
Finished by hot-rolling, annealing and pickling, characterized by white pickled surface |
Chemical industry equipment, Industrial tanks |
2B |
0.2-6.0mm |
Width: 1000/1219/1500/1800/2000mm; |
Finished by heat treatment, pickling after cold rolling, followed by skin pass line to be more brighter and smooth surface |
General Application Medical Instruments,Tableware |
No. BA |
0.2-3.0mm |
Width: 1000mm,1219mm; |
Bright heat treatment after cold rolling |
Kitchen utensil, kitchen ware,architectural purpose |
NO.4 Satin |
0.3-8.0mm |
Width: 1000/1219/1500mm; |
Polishing with No. 150 to No.320 mesh abrasivesThe most popular finishes |
Milk & Food processing acilities, Hospital Equipment, Bath-tub |
8K Mirror |
0.3-10mm |
Width: 1000/1219/1500mm; |
A mirror-like reflective surface by polishing with finer abrasives over 800 mesh |
Reflector, Mirror, Interior-Exterior decoration forbuilding |
HL(Hairline) |
0.3-8mm |
Width: 1000/1219/1500mm; |
Finished by continuous linear polishing |
Architectural purposes, escalators, kitchen ware vehicles |
Steel is an alloy of iron and carbon. Stainless steels are steels containing at least 10.5% chromium, less than 1.2% carbon and other alloying elements. Stainless steel’s corrosion resistance and
mechanical properties can be further enhanced by adding other elements, such as nickel, molybdenum, titanium, niobium, manganese, etc.
Grade |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
N |
Cu |
201 |
≤0.15 |
≤0.75 |
5.5~7.5 |
≤0.060 |
≤0.03 |
16.00~18.00 |
3.5~5.5 |
- |
- |
0.08 |
202 |
≤0.15 |
≤1.00 |
7.5~10.00 |
≤0.060 |
≤0.03 |
17.00~19.00 |
4.0~6.0 |
- |
≤0.25 |
|
301 |
≤0.15 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
6.00~8.00 |
- |
||
302 |
≤0.15 |
≤1.00 |
≤2.00 |
≤0.035 |
≤0.03 |
17.00~19.00 |
8.00~10.00 |
- |
||
304 |
≤0.07 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
18.00~20.00 |
8.00~10.50 |
- |
||
304L |
≤0.030 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
18.00~20.00 |
9.00~13.00 |
- |
||
310S |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
24.00~26.00 |
19.00~22.00 |
- |
||
316 |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
10.00~14.00 |
2.00~3.00 |
||
316L |
≤0.03 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
16.00~18.00 |
12.00~15.00 |
2.00~3.00 |
||
321 |
≤0.08 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.03 |
17.00~19.00 |
9.00~13.00 |
- |
||
430 |
≤0.12 |
≤0.75 |
≤1.00 |
≤0.040 |
≤0.03 |
16.00~18.00 |
- |
|||
2205 |
≤0.03 |
≤1.00 |
≤2.00 |
≤0.030 |
≤0.015 |
22.00~23.00 |
4.5~6.5 |
2.5~3.5 |
||
2507 |
≤0.03 |
≤0.08 |
≤1.20 |
≤0.035 |
≤0.015 |
24.00~26.00 |
6.00~8.00 |
3.0~5.0 |
||
904L |
≤0.02 |
≤1.00 |
≤2.00 |
≤0.045 |
≤0.035 |
19.00~23.00 |
23.00~28.00 |
4.0~5.0 |
1.0~2.0 |
|
INCONEL 028 |
≤0.03 |
≤1.00 |
≤2.50 |
≤0.030 |
≤0.030 |
≤28.0 |
≤34.0 |
≤4.0 |
≤1.4 |
|
MONEL 400 |
≤0.30 |
≤0.5 |
≤2.00 |
- |
≤0.024 |
- |
≥63.0 |
- |
≤34.0 |
|
INCONEL 800 |
≤0.10 |
≤1.00 |
≤1.50 |
- |
≤0.015 |
≤23.0 |
≤35 |
4.0~5.0 |
- |
≤0.75 |
FAQ:
Q: What kind of work does your company do?
A: We are a business steel industry and trade. We mainly produces stainless steel plate/pipe/coil/round bars etc.
Q: What are the advantages of your company?
A: (1): Prime quality and Competitive price.
(2): Excellent experiences with after-sale service.
(3): Every process will be checked by responsible QC which insures every product's quality.
(4): Professional packing teams which keep every packing safely.
(5): Samples can be provided as your requirements.
Q: What is your terms of payment ?
A: Can be negotiated by both parties. If you have another question, pls feel free to contact us as below
Q: What about your price?
A: Our price is very competitive.
Pls feel free to contact us if you are interested in our products.
Q: How long is your delivery time?
A: Stock steel/Steel for simple cutting/Small amount of general standard steel: about 5-20 days for delivery; Custom steel/bulk steel: about 15-30 days for delivery. Contact us for specific delivery times.